الصفحة الرئيسية

يشغل المعهد العالى للطاقة موقعاً متميزا أمام مركز التدريب الهيدروليكى التابع  لوزارة الكهرباء و الطاقة  و قد قام المعهد بتجهيز و إعداد الورش و المعامل التالية لإستخدام طلاب المعهد.

1- معمل الحاسبات:

يوجد2 معمل للكمبيوتر احدهم لطلاب المعهد و مزود بطابعة ليزرو ماسح ضوئي و اخر مخصص لشبكة الانترنت .

 

 

 

2-  معمل القوى الكهربية:

تجرى فى هذا المعمل بمبانى المعهد تجارب القوى الكهربية بداية من شبكات النقل حتى دوائر التيار المستمر ذات الجهد العالى و هى من طراز LAB VOLT)) ، مغذيات انظمة القدرة- أحمال - متحكمات، وتدرس أيضا فى هذا المعمل مشاكل الأستقرارية.

3-  معمل إلكترونيات القوى:

يوجد معمل إلكترونيات القوى من طراز LAB-VOLT)) توجد به أجهزة ثيريستور ،موسفيت و أجهزة اخرى من اجهزة الإلكترونيات الحديثة، دوائر إلكترونية، موحدات، معاكسات و خطوط دوائر التيار المستمر ذات الجهد العالى كلها متاحة فى هذا المعمل إلى جانب المتحكمات الخطية و التفاضلية و التكاملية.

4- معمل الجهد العالى:

يوجد فى هذا المعمل أجهزة إختبار الزيت المزودة بأجهزة مبرمجة للحصول على النتائج فى شكل معين كذلك يمكن استخدام هذة الأجهزة فى إختبار العوازل الأخرى.

5- معمل التحكم الآلى:

يتاح فى هذا المعمل اختبارات للتحكم بالإضافة للمتحكمات المختلفة مثل المتحكمات الخطية و التفاضلية و التكاملية و هناك اربعة من المتحكمات المنطقية إثنان منهم صناعيتين و الأخرتين للتمرين و التجارب التحكمية الأخرى تجرى فى معمل التحكم الهيدروليكى التابع لوزارة الكهرباء و الطاقة.

6- معامل أنظمة الوقاية:

تتاح فى هذة المعامل كل التجارب العملية الخاصة بالوقاية لكل من المولدات و الخطوط و القضبان و الأحمال و المحولات.

تختبر أيضا الوقاية المسافية و الوقاية التفاضلية التى تحتوى على كلا من الأجزاء الكهربية و الميكانيكية و الألكترونية. و يوجد أيضا بالمعمل أجهزة الوقاية الحديثة.

7- معمل الألات الكهربية:

يحتوى هذا المعمل على كلا من محركات التيار المتردد و محركات التيار المستمر كما توجد ماكينات خاصة مثل المحركات التنافرية و المحركات الخطية و محركات الخطوة و المحركات التزامنية و محولات ثلاثية الاوجه تستخدم لإختبار الآداء و الوظيفة، كما توجد أجهزة قياس القدرة الفرملية و شدة المجال المغناطيسى.

8- معمل معوضات القدرة غير الفعالة:

يوجد معوض قدرة غير فعالة ذو سعة (10 ك فولت-امبير-غير فعال) فى كل من الحثى و السعوى مزود بإمكانية التحكم فى الفولت يدويا و اوتوماتيكيا، يزود المعوض بنظام تبريد لوحدات الترنزستور و الملفات كما يوجد مفتاح آخر لنظام التشغيل.

9- معمل أجهزة التيار المستمر ذو الضغط العالى:

يتاح فى هذا المعمل دراسة ربط عملية التحكم بالآداء يتكون من مأخذ – خطوط النقل للتيارات المستمرة – عاكس التيار المستمر، تشكل العمليات باشكال عديدة من دوائرها التحكمية.

10- معمل القياسات الكهربية:

يتاح به قياس أنماط خاصة مثل قياس مقاومة الأرض و كذلك قياس القيم الكهربية مثل (التيار -  القدرة – الجهد و المقاومة...... الخ).

11- معمل القياسات الميكانيكية:

توجد بالمعمل أجهزة رقمية حديثة تقوم بقياس الكميات الميكانيكية مثل الضغط و درجة الحرارة و السريان، كما يوجد جهازان لقياس درجة تلوث الهواء.

 

 

12- معمل الطاقة الشمسية:

ويشمل المعمل على لوحةP.V  و أجهزة قياس تستخدم فى قياس كفاءة الأنواع المتعددة للخلايا الشمسية المستخدمة فى توليد الكهرباء كما يوجد بالمعمل تجربة أخرى خاصة بالأنظمة الحرارية الشمسية و قياس كفاءة عملية التسخين الشمسية.

13- معمل الاحتراق:

توجد بالمعمل آلة إحتراق بالشرارة لقياس آداء عملية الإحتراق و القدرة الفرملية للمحرك كما يشمل المعمل على محلل للعادم لتحليل الغازات الناتجة عن عملية الإحتراق بالمحرك أو اى مصادر تلوث اخرى.

14- معمل الهيدروليكا:

يشمل المعمل على مضخة الغاز و السائل النفاث و أجهزة قياس تستخدم فى قياس معدل ذوبان الأكسجين و معدل سريان الغازات و السوائل و قياس الضغط، كما يشتمل المعمل على أجهزة قياس لزوجة الموائع.

15- معمل الآلات الهيدروليكية:

يوجد فى هذا المعمل مضخات هيدروليكية بانواع مختلفة، كما يتعاون المعهد بالاستفادة من المركز الهيدروليكى التابع  لوزارة الكهرباء و الطاقة  لتجارب تقوم بقياس آداء الانواع المتعددة من التوربينات (بلتون – فرانسيس – كابلان) و الانواع المختلفة من المضخات الموصلة على التوالى و الموصلة على التوازى. كما توجد أجهزة تقوم بقياس أجهزة التحكم الهيدروليكية.

16- معمل التبريد و التكييف الهوائى:

يحتوى هذا المعمل على أجهزة تبريد و تكييف الهواء و التى تقوم بقياس آداء أجهزة التبريد و المتغيرات داخلها. كما توجد أنواع متقدمة من أبراج التبريد حيث يمكن قياس السريان و المتغيرات الحرارية داخلها.

17- الورش:

تتكون الورش الخاصة بالمعهد العالى للطاقة بأسوان من ورشة خراطة (5 مخارط) و ورشة لحام (2 ترانس لحام و ماكينة لحام بنط) و ورشة تشغيل (مثقاب و شنيورات و مناشير). وعدد 6 مجموعات اللحام بالغاز. ويتم الاستعانة بورش المعهد الفني الصناعي بأسوان (البرادة – الحدادة – السباكة وخلافه)

18- معمل الطبيعة:

يحتوي هذا المعمل علي الاجهزة اللازمة لاجراء التجارب العملية الخاصة بمادة الطبيعة لطلاب المعهد . 

19- معمل اللغات:

يستخدم طلاب المعهد معمل اللغات الذى يسع لعشرين طالبا و ذلك لدراسة اللغة الأنجليزية.

20- معمل الكيمياء:

جاري انشاء معمل لاجراء التجارب العملية الخاصة بمادة الكيمياء لطلاب المعهد . 

            

معامل ميكانيكا الموائع والالات التوربيينية والحراريات
والتحكم الميكانيكى

 (1) FLUID MECHANICS AND TURBOMACHINES LABORATORY

(HYDRAULIC TRAINING CENTER, ASWAN)

 

No.

Unit

Unit Description

1.

Friction in pipes

Pipe friction in different types of pipes (Diameter, roughness, and length) is investigated in this unit by measuring the pressure drop across the pipes.

2.

Manometer

Different types of manometer is fixed in a panel and used to measure the pressure using such manometers.

3.

Center of pressure on plane surface

The unit is provided to determine the position of the center of pressure force on the rectangular face of torrid.

4.

Intensity of liquid pressure

The unit shows that the intensity of liquid pressure only on depth.

5.

Archimedes principle

To verify Archimedes’ principle.

6.

Parallel and series pump connections

Test unit fixed with two pumps connected on series or parallel as required. The performance of the connected pump is investigated using a computer program (Data Acquisition).

 

(2) MECHANICS PROCESS CONTROL LABORATORY EQUIPMENT 

No.

Unit

Unit Description

1.

Industrial Process Controller of Level, Temperature and pressure

·        Unit used to perform the following tests:

·        Closed loop proportional control of the level.

·        Closed loop proportional integral control of the level.

·        Closed loop proportional derivative control of the level.

·        Closed loop proportional integral derivative control of the level.

·        Closed loop proportional integral derivative control of the level with auto-tune.

·        Closed loop ON-OFF control of the temperature.

·        Closed loop proportional control of the temperature.

·        Closed loop proportional integral control of the temperature.

·        Closed loop proportional derivative control of the temperature.

·        Closed loop proportional integral derivative control of the temperature.

·        Closed loop proportional integral derivative control of the level with auto-tune.

·        Closed loop ON-OFF control of the pressure with pressure sensor.

·        Control of the level with programmable set point.

·        The unit is fitted with data acquisition system.

 

(3) THERMODYNAMICS AND COMBUSTION LABORATORY EQUIPMENT

 

No.

Unit

Unit Description

1.

Petrol Engine Test Rig Model

This unit allows the study of operation of an Otto cycle engine.

·      Unit used to perform the following tests:

·      Speed governor.

·      Volumetric efficiency.

·      Total hourly consumption at constant power.

·      Specific fuel consumption.

·      Wastes of carburant air.

·      Power transmitted to the brakes at variable speed.

2.

Refrigeration system trainer

The unit allows several tests on a refrigeration process under several condition of head load, condenser pressure, refrigeration pressure ,   etc.

3.

Fuel analyzer

This unit provides a complete fuel test.

4.

Portable exhaust analyzer

This unit provides to measure the exhaust gases contents (NOx, COX, …..).

 

(4) FLUID MECHANICS AND TURBOMACHINES LABORATORY EQUIPMENT 

No.

Unit

Unit Description

1.

Francis Turbine

Francis Turbine unit used to perform the following tests:

·      Performance of the hydraulic turbine under different conditions of head.

·      Performance of the hydraulic turbine under different conditions of blade position.

·      Performance of the hydraulic turbine under different conditions of turbine speed.

The unit is fitted with data acquisition system.

2.

Pelton Turbine

Pelton Turbine unit used to perform the following tests:

·      Performance of the hydraulic turbine under different conditions of head.

·      Performance of the hydraulic turbine under different conditions of turbine speed.

The unit is fitted with data acquisition system.

3.

Centrifugal Pump

Centrifugal Pump test rig used to perform the following tests:

·      Pump characteristic (head-discharge relation).

·      System head characteristic

·      The performance of the pump under different conditions of speed head and discharge.

The unit is fitted with data acquisition system.

4.

Axis Flow Pump

Axis Flow Pump test rig used to investigate the performance of the pump under different conditions of speed head and discharge.

 

5.

Reciprocating compressor

Measurement of air pressure, temperature, and pressure on such unit is provided to investigate the performance of two cylinders single acting reciprocating compressor.

6.

Viscometer

Viscometer instrument with many samples of liquids is provided in this unit.

7.

Measuring instrument

Flow and velocity meters such as (Ultrasonic flow meter, hot wire anemometer, orifice flow meter, etc.), temperature, pressure, dissolved Oxygen, solar radiation, etc.

  ELECTRICAL POWER, MACHINES, AND POWER ELECTRONICS LABORATORIES

(1) Electric Power Transmission System 220/380 V-50 Hz Lab Equipment: 

QTY

Description

1

Mobile Workstation

1

DC Motor/Generator

1

Four pole squirrel cage induction motor

1

Three phase wound rotor induction motor

1

Three phase synchronous Motor/Generator

1

Resistive Load

1

Inductive Load

2

Three Phase Transition line

1

Capacitive  load

1

Three phase transformer Ratio 1:1

1

Three phase regulating autotransformer

1

DC Voltmeter/Ammeter

1

AC Ammeter

1

AC Voltmeter

2

Three Phase Wattmeter/Varmeter

1

Phase meter

1

Power Supply

1

Phase Shift Indicator

1

Inertia Wheel

1

Timing belt

1

Connection Leads

 (a) The following experiments are available:

1.      Safety and the power supply

2.      Phase sequence

3.      Real power and reactive power

4.      Power flow and voltage regulation of a simple transmission line

5.      Phase angle and voltage drop between sender and receiver

6.      Parameters which affect real and reactive power flow

7.      Parallel lines, transformers and power handling capacity

8.      The alternator

9.      The synchronous motor

 (b) Transformer protection experiments:

1.      Three phase transformer connections

2.      Distribution transformer connections

3.      Transformer magnetizing inrush & winding faults

4.      Current transformers polarity, ratio & saturation

5.      Potential transformers polarity, ratio & saturation

6.      Current transformer connection differential interposing circuits

7.      Current transformer connections for power transformer

8.      Overcurrent protection of 2-phase power transformers.

9.      Differential protection of 3-phase power transformers.

10. Overcurrent , restricted earth fault and differential protection

 (c) Distribution freeder protection experiments:

1.      Protection with the coordination

2.      Protection with current coordination

3.      Protection with time and current coordination

4.      Feeder protection with directional earth fault

5.      Ring bus protection with directional relays

6.      Dual feeder with partial differential protection

7.      Auto reclosing

 (d) Generator protection experiments:

1.      Characteristics of the Lab-Volt 8241 synchronous Motor/Generator

2.      Overcurrent protection of a synchronous generator

3.      Unbiased differential protection of a synchronous generator

4.      Reverse power protection of a synchronous generator

5.      Negative sequence protection of a synchronous generator

6.      Rotor earth fault protection of a synchronous generator

7.      Loss of filed protection of a synchronous generator

8.      Generator system protection

9.      Under and over voltage protection of a synchronous generator 

(e) Motor protection experimens:

1.      Differential protection of an induction motor

2.      Under voltage protection of an induction motor

3.      phase reversal protection of an induction motor

4.      overcurrent protection of an induction motor

5.      phase balance protection of an induction motor

6.      load (power factor) protection of an induction motor

(2) Power Electronics Lab Equipment: 

(a) Familiarization with the Lab-Volt Power Electronics Lab Equipment:

QTY

Description

1

Mobile Workstation

1

DC Motor/Generator

1

Four pole squirrel cage induction motor

1

Resistive Load

1

Smoothing Inductors

1

Capacitive  load

2

DC Voltmeter/Ammeter

1

AC Ammeter

1

AC Voltmeter

2

Three Phase Wattmeter/Varmeter

1

Tandem Rheostat

1

Power supply

1

Power MOSFETS

1